01-30
2020year
OpenSLS - 3D printing

You may recall, that a little over a month ago, we did a story on a man named Andreas Bastian, who had 3D printed mesostructured material. When I was covering the story and speaking with Bastian

01-30
2020year
Sintering Fundamentals - Abbott Furnace Company - Sintering

Oxide Reduction. The oxide layer must be reduced to allow the particles to come in contact. The reduction is the result of the reaction between the furnace atmosphere and the oxygen in the oxide layer. A typical sintering furnace atmosphere will contain Hydrogen and/or Carbon Monoxide to react with the Oxygen on the surface of the metal particles.

01-30
2020year
500ºC Vacuum Lamination Press with Two 4"x 4" Heating Plate

YLJ-VHP5-4 (update from EQ-VHP-5T-4) is a CE Certified electric vacuum lamination hot press designed for wafer bonding or thin-film transformations up to 100mm x 100mm. It has the max. the working temperature of 500ºC along with the max. the pressure of 20 Metric Tons.

01-30
2020year
Vacuum Hot Press Furnaces For Sintering Advanced Ceramics

The vacuum hot pressure furnaces is used kinds of ceramic as below: metallurgy(MIM and CIM), cemented carbide, technical ceramics (MLCC, LTCC, HTCC), 3D-Printing etc. Products Composing:

01-30
2020year
Keith Company | Sintering Furnaces | Carbonization Furnaces

Keith Company also builds pyrolysis furnaces (carbonization furnaces) for carbon composites which requires less than 100ppm oxygen in the vessel. Sintering process are done at temperatures between 900degC [1650degF] and 1250degC [2300degF].

01-30
2020year
High-temperature furnace, High-temperature oven - All

VACUUM FURNACES ADDITIVE MANUFACTURING In 3D printing, metal parts are made by successive layers of metal powders. The rapid cooling following the laser step causes variations in the parts' microstructure, phase changes

01-30
2020year
Hot pressing - Wikipedia

Hot pressing is a high-pressure, low-strain-rate powder metallurgy process for forming of a powder or powder compact at a temperature high enough to induce sintering and creep processes. This is achieved by the simultaneous application of heat and pressure. Hot pressing is mainly used to fabricate hard and brittle materials.

01-30
2020year
Used Vacuum Sintering Furnaces for sale. Top quality

AVS Vacuum Debinding/ Sintering Furnace #VF282. This is a horizontal graphite vacuum debinding sintering furnace for steel MIM parts completely rebuilt from top to bottom by AVS in 2010. Working volume – approximately 18 cubic feet, 28" wide x 26" high x 42" l

01-30
2020year
China 10t Hot Press Furnace, Argon (Ar) Hot Press Furnace

metallurgy(MIM and CIM), cemented carbide, technical ceramics (MLCC, LTCC, HTCC), 3D-Printing etc. Vacuum hot-pressing furnace is mainly used for high-temperature sintering and hot pressing of powder ceramic materials and powder sintered materials under vacuum (or protective atmosphere), and can also be used for other metal or non-metal materials under vacuum (or protective atmosphere).

01-30
2020year
OpenSLS - 3D printing

OpenSLS – An Open Source Project Creates a Sub-$15K Selective Laser Sintering 3D Printer. Those familiar with SLS technology, that is used by 3D Systems' large SLS printers, know that there is a large amount of heat involved in the process. OpenSLS, however, uses a different type of technology.

01-30
2020year
Cold Hydrostatic Sintering: From shaping to 3D printing

On the other side, consolidation under hydrothermal sintering conditions has been proven feasible for silica at 300 °C, 190 MPa, 90 min, and α-quartz at 350 MPa, 300 °C, 90 min . Using as model system spherical glass particles, Hosoi et al. identified the consolidation mechanism occurring during hydrothermal hot press.

01-30
2020year
Our Equipment Archives - The Furnace Source

Features: • Standard one-year warranty. • Rough vacuum, partial pressure, or full atmosphere operation with nitrogen or argon. • Manual valve operation, automatic ramps and soaks with Yokogawa UP55.

01-30
2020year
Sintering Furnaces for Powder Metal - Abbott Furnace Company

Abbott Furnace Company manufactures continuous belt sintering furnaces used in the powder metal industry. Sintering is a heat treatment applied to a powder compact in order to impart strength and integrity. The temperature used for sintering is below the melting point of the major constituent of the Powder Metal material.

01-30
2020year
Heating machine

3d Sublimation Heat Press Vacuum Machine. 3d Sublimation Heat Press Vacuum Machine Description: A 3D sublimation heat transfer printing machine is the machine that presses a transfer onto an imprintabl. more>

01-30
2020year
FCT Systeme GmbH

Gas Pressure Sintering Plants GPS. The devices are particularly suitable for sintering such types of ceramics or metals, which tend to decomposition at elevated temperatures or which do not sinter to high densities in standard sintering operations. This process has not the limitations with respect to the shape of the manufactured parts as in hot

01-30
2020year
Fabrication of SiC whisker-reinforced SiC ceramic matrix

Numerous ceramic parts have been fabricated by the 3D printing method of binder jetting [,,,,,, ]. The raw materials used for binder jetting are ceramic powders, whose flowability can determine the printability of parts [13,14].

01-30
2020year
Sintering and Solution Treatments for Metal 3D-Printed Parts

Jul 18, 2016 · Sintering and Solution Treatments for Metal 3D-Printed Parts Dr. Markus Chmielus (right), assistant professor in the Department of Mechanical Engineering and Materials Science at the University of Pittsburgh.

01-30
2020year
Metal 3D Printing: Laser Sintering vs. Bulk Sintering in a

Much like MIM, 3D printing technologies such as binder jetting, material jetting, and other bind and sinter processes create green parts that require sintering in a furnace to attain full density.

01-30
2020year
Custom High-Temperature Lab Ovens and Furnaces

The types of labs using laboratory furnaces range from dental labs to university labs to quality-control labs. Accordingly, each of these laboratories have very different needs. For example, dental furnaces use high-temperature lab ovens to perform zirconia binder burnout, firing, and sintering.

01-30
2020year
Sintering in the Powder Metallurgy Process

Sintering is a heat treatment applied to a powder compact in order to impart strength and integrity. The temperature used for sintering is below the melting point of the major constituent of the Powder Metallurgy material.